Skip to main content

Tax on a Work Order Line

See the tax rate on a line before you save it, leave tax off a line with Exclude tax, and bill a tax-exempt customer so your books and your invoice agree.

Tax on a work order is set per line, from each item's own tax setup. There is no tax setting on the work order or the job, so a taxable part and untaxed labor sit happily on the same job.

  • Who can do this: Admin or Dockmaster can tick Exclude tax. Changing an item's tax setup needs Admin or Finance.

  • Where: Service → Work Orders for the line; Sales → Items for the item.

  • Before you start: your item tax rates should already be right. Exclude tax is for exceptions, not for fixing an item that's taxed wrong.

See the rate before you save

Every parts and labor line shows a Tax rate beside Rate and Qty. It's read-only and comes from the item, so the figure you quote a customer standing at the counter is the figure that gets billed. Where more than one tax applies to the item, hover the rate to see them broken out.

Leave tax off one line

Tick Exclude tax on a line and that line's tax goes to zero. The Tax rate changes to 0% so you can see at a glance that it's been waived.

It applies to that one line of that one job. The line beside it is untouched, and so is the item everyone else in the yard is using.

💡

Good to know: if the checkbox is greyed out, there's no tax on that line to exclude.

An item you never charge tax on

If you never charge tax on something — most yards don't tax labor — fix the item rather than ticking the box every time.

  1. Go to Sales → Items and open the item.

  2. Set its tax rate to 0.

  3. Tick Tag item as non-taxable so it's reported as a non-taxable sale.

Both steps matter. The tag on its own doesn't stop the item charging tax — Dockwa warns you on the item form when a tagged item still has a rate. With the item set up properly, every job that uses it comes through untaxed and nobody has to remember anything. See Set Up Parts and Labor Items For Work Orders.

Keep Exclude tax for genuine one-offs.

Billing a tax-exempt customer

This takes two settings in two systems, and you need both.

  • Exclude tax, in Dockwa. Stops the customer being charged. It's per line, so a job with four taxable lines needs four ticks, every job.

  • The tax-exempt flag on the customer, in your accounting system. Doesn't change what you bill. It changes which column the sale lands in on your sales tax return, and it's where the customer's certificate lives.

Neither one does the other's job:

What you set

Customer is charged

Filed as

Result

Neither

Sales tax

Taxable sales

Right for an ordinary customer

Exclude tax only

Nothing

Taxable sales, no tax

Reads as under-collection

Accounting flag only

Sales tax

Non-taxable sales

Billed wrong and filed wrong

Both

Nothing

Exempt sales, no tax

Correct

Before you send, check the Generate Invoice review: a tax-exempt customer's invoice should show no sales tax at all. If tax is showing, a line was missed. See Invoice a Work Order.

⚠️

Exclude tax does not make a customer tax exempt. It zeroes the tax on one line of one job. It stores no exempt status, holds no certificate, and applies no rule to anything else you bill them. Dockwa doesn't remit sales tax for you — verify the customer's documentation and check with your own tax advisor before waiving tax for anyone.

Not available yet

  • A tax-exempt flag on the customer in Dockwa. Tick Exclude tax on each taxable line.

  • Excluding tax across a whole job or invoice in one go. It's per line.

  • Storing an exemption certificate in Dockwa. Keep it in your accounting system with the customer.

  • Editing a line's tax rate on the work order. The rate is read-only and comes from the item.

Common questions

I marked the customer exempt in my accounting system. Why were they still charged tax?

Because that flag never reaches Dockwa. Dockwa bills whatever the item's tax rate says until you tick Exclude tax on the line. The flag only changes how the sale is reported.

Why does my liability report show taxable sales with no tax collected?

Exclude tax on a taxable item leaves the sale in the taxable column with nothing against it. That's accurate — it was a taxable sale that collected nothing. Flagging the customer in your accounting system is what moves it into the exempt column.

Can I tick Exclude tax on a job that's already complete?

Yes, right up until the line is invoiced. You don't need to reopen the job.

Does a discount change the tax?

Yes. Tax is calculated on the amount left after the discount. See Discount a Line on a Work Order.

How do I check an exemption at filing time?

On your sales tax liability report, read the exempt column separately from non-taxable, and group by exemption reason where your accounting system supports it. That grouping is what substantiates the exemption.

Related articles

Did this answer your question?